305 publications from this institution
The effect of meat marinating with aqueous extract of Ilex meserveae dried leaves on dry-aged beef quality was investigated. Shear force, TBARS value, color parameters, fatty acid profile, and sensory properties were evaluated in beef cuts dry-aged for 21 days. The use of Ilex meserveae dried leaves as marinade at 0.5, 1.0, and 2.0% <math xmlns="http://www.w3.org/1998/Math/MathML" id="M1"> <mtext>w</mtext> <mo>/</mo> <mtext>v</mtext> </math> did not affect the shear force and color parameters of dry-aged beef. The marinating of beef cuts with Ilex meserveae resulted in efficient prevention of lipid oxidation without impairing sensory acceptability. Aqueous extract Ilex meserveae can be applied as a natural ingredient in meat marinade to prevent peroxidation.
There are insufficient data for the development of process design criteria for constructed wetlands systems based on submerged plants as a major treatment agent. The aim of the study was to evaluate the oxygen transfer capacity (OTC) of E. densa, in relation to wet plants’ mass (w.m.), and the influence of E. densa on the oxygen concentration and contaminants’ removal efficiency from municipal wastewater. The obtained oxygen concentration and temperature data allowed to calculate the OTC values (mg O2·L−1·h−1), which had been related to wet plants’ mass unit (mg O2·L−1·h−1·g w.m.−1). The efficiency of wastewater treatment was determined in relation to initial wastewater content in the mixture of wastewater and tap water (0%, 25%, 50%, and 100%) during 3 days of the experiment duration. The simulation of day and night conditions was done by artificial lighting. Before and after finishing the second experiment, the COD, Ntotal, and P-PO4 concentration were analyzed in wastewater solutions. The OTC ranged from 3.19 to 8.34 (mgO2·L−1·h−1·g w.m.−1), and the increase of OTC value was related to the increase of wet plant’s mass. The research showed that E. densa affected positively on the wastewater treatment efficiency, and the highest efficiency was achieved in 25% wastewater solution: 43.6% for COD, 52.9% for Ntotal, 14.9% for P-PO4.
The effectiveness of nitrogen removal in vertical-flow filters with double-layer filling composed of lightweight aggregate made of fly ashes from sewage sludge thermal treatment (FASSTT LWA) and gravel at a varying hydraulic load was determined. Synthetic wastewaters containing 47 mg/L of total nitrogen (TN) were fed into 15 filter columns filled with gravel and FASSTT LWA (gravel was the bed's lower layer, whereas the top layer of the FASSTT LWA constituted 0, 12, 25, 50, and 100% of the depth of the column) at hydraulic loads of 3, 5, and 7 mm/day. The study demonstrated a significant TN removal by the filters, which was accompanied by a high concentration of NO3-N in the effluent. The results point to differentiated effectiveness of NH4-N removal by both the FASSTT LWA and gravel. The highest TN removal rate reaching up to 74.93% was achieved in the filter column with 100% FASSTT LWA content, irrespective of the hydraulic load applied.
In the wake of economic and population growth, increased wastewater production poses a challenge related to sewage sludge treatment, which is problematic given its high moisture content, amount, and hazardous characteristics. This study focuses on the hydrothermal carbonization of sewage sludge to produce carbonous material–hydrochar, which may be an alternative to fossil fuels. The effect of process parameters, namely, temperature (180, 240, 300 °C) and duration time (30, 90, 180 min), on hydrochar properties (proximate and ultimate analysis, heating values) and process performance were studied. Obtained results indicate and confirm that hydrothermal carbonization, especially temperature increase, improves the fuel properties of carbonized sewage sludge. The highest low heating value was obtained for hydrochar derived at 300 °C in 180 min (~23 MJ × kg−1). The highest energy gain was noted for hydrochar derived at 240 °C in 180 min (~23%). As well as relatively high mass and energy yield in comparison to other hydrochars, these parameters are considered the most favorable for sewage sludge hydrothermal carbonization. However, high energy consumption (over 1300 kJ × g−1) suggests that more research on the process’s economical efficacy is required.
Excessive amounts of sodium cations (Na+) in water is an important limiting factor to reuse poor quality water in agriculture or industry, and recently, much attention has been paid to developing cost-effective and easily available water desalination technology that is not limited to natural resources. Biochar seems to be a promising solution for reducing high loads of inorganic contaminant from water and soil solution, and due to the high availability of biomass in agriculture and forestry, its production for these purposes may become beneficial. In the present research, wheat straw, sunflower husk, and pine-chip biochars produced at 250, 450 and 550 °C under simple torrefaction/pyrolysis conditions were chemically modified with ethanol or HCl to determine the effect of these activations on Na sorption capacity from aqueous solution. Biochar sorption property measurements, such as specific surface area, cation exchange capacity, content of base cations in exchangeable forms, and structural changes of biochar surface, were performed by FTIR and EPR spectrometry to study the effect of material chemical activation. The sorption capacity of biochars and activated carbons was investigated by performing batch sorption experiments, and adsorption isotherms were tested with Langmuir’s and Freundlich’s models. The results showed that biochar activation had significant effects on the sorption characteristics of Na+, increasing its capacity (even 10-folds) and inducing the mechanism of ion exchange between biochar and saline solution, especially when ethanol activation was applied. The findings of this study show that biochar produced through torrefaction with ethanol activation requires lower energy demand and carbon footprint and, therefore, is a promising method for studying material applications for environmental and industrial purposes.
