Both passive and active intelligent reflecting surfaces (IRSs) can be deployed in complex environments to enhance wireless network coverage by creating multiple blockage-free cascaded line-of-sight (LoS) links. In this paper, we study a multi-passive/active-IRS (PIRS/AIRS) aided wireless network with a multi-antenna base station (BS) in a given region. First, we divide the region into multiple non-overlapping cells, each of which may contain one candidate location that can be deployed with a single PIRS or AIRS. Then, we show several trade-offs between minimizing the total IRS deployment cost and enhancing the signal-to-noise ratio (SNR) performance over all cells via direct/cascaded LoS transmission with the BS. To reconcile these trade-offs, we formulate a joint multi-PIRS/AIRS deployment problem to select an optimal subset of all candidate locations for deploying IRS and also optimize the number of passive/active reflecting elements deployed at each selected location to satisfy a given SNR target over all cells, such that the total deployment cost is minimized. However, due to the combinatorial optimization involved, the formulated problem is difficult to be solved optimally. To tackle this difficulty, we first optimize the reflecting element numbers with given PIRS/AIRS deployed locations via sequential refinement, followed by a partial enumeration to determine the PIRS/AIRS locations. Simulation results show that our proposed algorithm achieves better cost-performance trade-offs than other baseline deployment strategies.
The manufacturing of integrated circuits (ICs) has been continuously improved through the advancement of fabrication technology nodes. However the lithography hotspots (HSs) caused by optical diffraction problems seriously affect the yield and reliability of ICs. Although lithography simulation can accurately capture the HSs through physically simulating the lithography process, it requires a lot of computing resources, which usually takes > 100 CPU · <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$h$</tex> /mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> [1]. Due to the image recognition nature, the state-of-the-art HS identification algorithms based on deep learning have obvious advantages in reducing run time comparing to the traditional algorithms. However, its accuracy still needs to be enhanced since there are many false alarms of non-hotspots (NHSs) and escapes of the real HSs, which makes it difficult to be a signoff technique. In this paper, we propose two enhancements in HS identification. First, a hybrid deep learning model is proposed in lithography HS identification, which includes a CNN model to combine physical features. Second, an ensemble learning method is proposed based on multiple submodels. The proposed enhanced model and method can achieve high HS identification accuracy on the benchmarks 1–4 of the ICCAD 2012 dataset with recall> 98.8%. In addition, it can achieve even 100% recall on the benchmark 1 and benchmark 3 while maintaining the precision at a high level with 53.6% and 87.1%, respectively. Moreover, for the first time it can achieve not only 100% recall on benchmark 5, but also high precision of 61.8%, which is much higher than any published deep learning methods for HSs identification, as far as we know. The proposed model and methodology can be applied in industrial IC designs due to its effectiveness and efficiency.
This letter studies an emerging wireless communication intervention problem at the physical layer, where a legitimate spoofer aims to spoof a malicious link from Alice to Bob, by replacing Alice's transmitted source message with its target message at Bob side. From an information-theoretic perspective, we are interested in characterizing the maximum achievable spoofing rate of this new spoofing channel, which is equivalent to the maximum achievable rate of the target message at Bob, under the condition that Bob cannot decode the source message from Alice. We propose a novel combined spoofing approach, where the spoofer sends its own target message, combined with a processed version of the source message to cancel the source message at Bob. For both cases when Bob treats interference as noise or applies successive interference cancelation, we obtain the maximum achievable spoofing rates by optimizing the power allocation between the target and source messages at the spoofer.
There is a growing interest in energy efficient or so-called "green" wireless communication to reduce the energy consumption in cellular networks. Since today's wireless terminals are typically equipped with multiple network access interfaces such as Bluetooth, Wi-Fi, and cellular networks, this paper investigates user terminals cooperating with each other in transmitting their data packets to the base station (BS), by exploiting the multiple network access interfaces, called inter-network cooperation. We also examine the conventional schemes without user cooperation and with intra-network cooperation for comparison. Given target outage probability and data rate requirements, we analyze the energy consumption of conventional schemes as compared to the proposed inter-network cooperation by taking into account both physical-layer channel impairments and upper-layer protocol overheads. It is shown that distances between different network entities (i.e., user terminals and BS) have a significant influence on the energy efficiency of proposed inter-network cooperation scheme. Specifically, when the cooperating users are close to BS or the users are far away from each other, the inter-network cooperation may consume more energy than conventional schemes without user cooperation or with intra-network cooperation. However, as the cooperating users move away from BS and the inter-user distance is not too large, the inter-network cooperation significantly reduces the energy consumption over conventional schemes.
In this paper, we consider a mmWave massive multiple-input multiple-output (MIMO) communication system with one static base station (BS) serving a fast-moving user, both equipped with a very large array. The transmitted signal arrives at the user through multiple paths, each with a different angle-of-arrival (AoA) and hence Doppler frequency offset (DFO), thus resulting in a fast time-varying multipath fading MIMO channel. In order to mitigate the Doppler-induced channel aging for reduced pilot overhead, we propose a new angular-domain selective channel tracking and Doppler compensation scheme at the user side. Specifically, we formulate the joint estimation of partial angular-domain channel and DFO parameters as a dynamic compressive sensing (CS) problem. Then we propose a Doppler-aware-dynamic variational Bayesian inference (DD-VBI) algorithm to solve this problem efficiently. Finally, we propose a practical DFO compensation scheme which selects the dominant paths of the fast time-varying channel for DFO compensation and thereby converts it into a slow time-varying effective channel. Compared with the existing methods, the proposed scheme can enjoy the huge array gain provided by the massive MIMO and also balance the tradeoff between the CSI signaling overhead and spatial multiplexing gain. Simulation results verify the advantages of the proposed scheme over various baseline schemes.
In recent decades, droughts have become more frequent and severe due to global warming, and the amount of water in dams and reservoirs has decreased in many regions. To alleviate the water shortage problem, we modeled the water allocation in dams to achieve the optimal combination of water and electricity. A multi-objective optimization model for water allocation in dams was developed. A grid method was used to rasterize the dams and calculate the reservoir capacity of the dams. The multi-objective optimization model was used to improve water distribution schemes in five states based on the collection of water and electricity consumption data from five states in recent years. The consumption time for water transport and power generation, as well as the amount of water supplied, is minimized while meeting the water supply and power demand and providing surplus water for Mexico. In the next step, game theory was used to solve the conflict problem of allocating water among the four uses and to transform the problem into a utility non-transferable game model. Considering the differences in water use by state, the states were typed into three categories: hydro, industrial and non-industrial states. Different weights were assigned to the four types of water use in different types of states, taking into account the different importance attached to different water use in different regions. The allocation results for the different states were obtained.
Integrating the unmanned aerial vehicles (UAVs) into the cellular network is envisioned to be a promising technology to significantly enhance the communication performance of both UAVs and existing terrestrial users. In this paper, we first provide an overview on the two main research paradigms in cellular UAV communications, namely, cellular-enabled UAV communication with UAVs as new aerial users served by the ground base stations (GBSs), and UAV-assisted cellular communication with UAVs as new aerial communication platforms serving the terrestrial users. Then, we focus on the former paradigm and study a new UAV trajectory design problem subject to practical communication connectivity constraints with the GBSs. Specifically, we consider a cellular-connected UAV in the mission of flying from an initial location to a final location that are given, during which it needs to maintain reliable communication with the cellular network by associating with one of the available GBSs at each time instant that has the best line-of-sight channel (or shortest distance) with it. We aim to minimize the UAV's mission completion time by optimizing its trajectory, subject to a quality-of-connectivity constraint of the GBS-UAV link specified by a minimum receive signal-to-noise ratio target, which needs to be satisfied throughout its mission. To tackle this challenging non-convex optimization problem, we first propose an efficient method to verify its feasibility via checking the connectivity between two given vertices on an equivalent graph. Next, by examining the GBS-UAV association sequence over time, we obtain useful structural results on the optimal UAV trajectory, based on which two efficient methods are proposed to find high-quality approximate trajectory solutions by leveraging the techniques from graph theory and convex optimization. The proposed methods are analytically shown to be capable of achieving a flexible tradeoff between complexity and performance, and yielding a solution in polynomial time with the performance arbitrarily close to that of the optimal solution. Numerical results further validate the effectiveness of our proposed designs against benchmark schemes. Finally, we make concluding remarks and point out promising directions for future work.
IRS is a new and revolutionizing technology that is able to significantly improve the performance of wireless communication networks, by smartly reconfiguring the wireless propagation environment with the use of massive low-cost passive reflecting elements integrated on a planar surface. Specifically, different elements of an IRS can independently reflect the incident signal by controlling its amplitude and/or phase and thereby collaboratively achieve fine-grained 3D passive beamforming for directional signal enhancement or nulling. In this article, we first provide an overview of the IRS technology, including its main applications in wireless communication, competitive advantages over existing technologies, hardware architecture as well as the corresponding new signal model. We then address the key challenges in designing and implementing the new IRS-aided hybrid (with both active and passive components) wireless network, as compared to the traditional network comprising active components only. Finally, numerical results are provided to show the great performance enhancement with the use of IRS in typical wireless networks.
