Publications

Abstract The performance of III-Nitride based Light Emitting Diodes (LEDs), LASERs, GaN/AlGaN MODFETs (Modulation-doped Field Effect Transistors) and HEMTs (High Electron Mobility Transistors) have been improved dramatically over the past few years [1,2], despite the relatively poor material quality of GaN, as compared to GaAs, for example. The intrinsic properties of the materials system make it extremely well suited to both optoelectronic and microwave power transistor applications. Typically, GaN is grown on substrates such as GaAs, Al2O3 (sapphire) or SiC with large lattice mismatch. This has usually resulted in an extremely high defect density in the GaN layer. The growth of GaN on lithium gallate LiGaO2 (LGO) affords many advantages compared to all other available substrates. LGO offers the smallest average lattice mismatch of any available substrate for the Ill-nitrides. This facilitates the growth of high quality GaN directly on Lithium Gallate without the need for a defective buffer to decouple the strain associated with the large lattice mismatch of other substrates [3].

Electromagnetic generators (EMGs) and triboelectric nanogenerators (TENGs) are the two most powerful approaches for harvesting ambient mechanical energy, but the effectiveness of each depends on the triggering frequency. Here, after systematically comparing the performances of EMGs and TENGs under low-frequency motion (<5 Hz), we demonstrated that the output performance of EMGs is proportional to the square of the frequency, while that of TENGs is approximately in proportion to the frequency. Therefore, the TENG has a much better performance than that of the EMG at low frequency (typically 0.1–3 Hz). Importantly, the extremely small output voltage of the EMG at low frequency makes it almost inapplicable to drive any electronic unit that requires a certain threshold voltage (∼0.2–4 V), so that most of the harvested energy is wasted. In contrast, a TENG has an output voltage that is usually high enough (>10–100 V) and independent of frequency so that most of the generated power can be effectively used to power the devices. Furthermore, a TENG also has advantages of light weight, low cost, and easy scale up through advanced structure designs. All these merits verify the possible killer application of a TENG for harvesting energy at low frequency from motions such as human motions for powering small electronics and possibly ocean waves for large-scale blue energy.

Ceria (CeO2) based ceramics have been widely used for many applications due to their unique ionic, electronic, and catalytic properties. Here, we report our findings in investigating into the redox processes of undoped and Sm-doped CeO2 ceramics stimulated by high-energy electron beam irradiation within a transmission electron microscope (TEM). The reduced structure with oxygen vacancy ordering has been identified as the CeO1.68 (C-Ce2O3+δ) phase via high-resolution TEM. The reduction of Ce4+ to Ce3+ has been monitored by electron energy-loss spectroscopy. The decreased electronic conductivity of the Sm-doped CeO2 (Sm0.2Ce0.8O1.9, SDC) is revealed by electron holography, as positive electrostatic charges accumulated at the surfaces of SDC grains under electron beam irradiation, but not at CeO2 grains. The formation of the reduced CeO1.68 domains corresponds to lattice expansion compared to the CeO2 matrix. Therefore, the growth of CeO1.68 nuclei builds up strain inside the matrix, causing annihilation of ...

Abstract The soft‐contact freestanding rotary triboelectric nanogenerator (FR‐TENG), with the capabilities of high output performance and excellent efficiency, presents interesting applications in driven nonequilibrium plasma jets, mass spectrometry, electrospinning, and so on. For enhancing the output performance of FR‐TENG, detailed and in‐depth research focusing on the design method is discussed in this paper, mainly consisting of the following four parts: 1) design reasonable geometric structure, 2) select triboelectric layers, 3) choose a reasonable signal acquisition, and 4) investigate influencing factors. Benefiting from this four‐step systematic research, a modified FR‐TENG with better output performance is successfully constructed. A corresponding open‐circuit voltage density of 1.27 × 10 5 V m −2 is achieved, which is over twofold higher compared to the largest one among the previous similar articles. Therefore, the four‐step systematic research is demonstrated to remarkably enhance the output performance of the soft‐contact FR‐TENG. This work not only presents a modified FR‐TENG with ultrahigh voltage density that inhibits bacterial corrosion, enables high‐voltage electrostatic dust removal, and enables impressive current cathodic protection of marine pipelines and urban buried pipelines, but also can be regarded as guidance for the design of soft‐contact FR‐TENG.

Perovskite ferroelectric nanowires have rarely been used for the conversion of tiny mechanical vibrations into electricity, in spite of their large piezoelectricity. Here we present a lead-free NaNbO3 nanowire-based piezoelectric device as a high output and cost-effective flexible nanogenerator. The device consists of a NaNbO3 nanowire–poly(dimethylsiloxane) (PDMS) polymer composite and Au/Cr-coated polymer films. High-quality NaNbO3 nanowires can be grown by hydrothermal method at low temperature and can be poled by an electric field at room temperature. The NaNbO3 nanowire–PDMS polymer composite device shows an output voltage of 3.2 V and output current of 72 nA (current density of 16 nA/cm2) under a compressive strain of 0.23%. These results imply that NaNbO3 nanowires should be quite useful for large-scale lead-free piezoelectric nanogenerator applications.

Abstract Increasing performance demand associated with the short lifetime of consumer electronics has triggered fast growth in electronic waste, leading to serious ecological challenges worldwide. Herein, a robust strategy for judiciously constructing flexible perovskite solar cells (PSCs) that can be conveniently biodegraded is reported. The key to this strategy is to capitalize on meniscus‐assisted solution printing (MASP) as a facile means of yielding cross‐aligned silver nanowires in one‐step, which are subsequently impregnated in a biodegradable elastomeric polyester. Intriguingly, the as‐crafted hybrid biodegradable electrode greatly constrains the solvent evaporation of the perovskite precursor solution, thereby generating fewer nuclei and in turn resulting in the deposition of a large‐grained dense perovskite film that exhibits excellent optoelectronic properties with a power conversion efficiency of 17.51% in PSCs. More importantly, the hybrid biodegradable electrode‐based devices also manifest impressive robustness against mechanical deformation and can be thoroughly biodegraded after use. These results signify the great potential of MASP for controllably assembling aligned conductive nanomaterials for biodegradable electrodes. As such, it represents an important endeavor toward environmentally friendly, multifunctional and flexible electronic, optoelectronic, photonic, and sensory materials and devices.

Using phosphorus-doped ZnO nanowire (NW) arrays grown on silicon substrate, energy conversion using the p-type ZnO NWs has been demonstrated for the first time. The p-type ZnO NWs produce positive output voltage pulses when scanned by a conductive atomic force microscope (AFM) in contact mode. The output voltage pulse is generated when the tip contacts the stretched side (positive piezoelectric potential side) of the NW. In contrast, the n-type ZnO NW produces negative output voltage when scanned by the AFM tip, and the output voltage pulse is generated when the tip contacts the compressed side (negative potential side) of the NW. In reference to theoretical simulation, these experimentally observed phenomena have been systematically explained based on the mechanism proposed for a nanogenerator.

Aligned oblique nanowire arrays (AONWAs; top image) with controllable obliquity, NW diameter, length, and density are produced by a novel method. A mechanism of array formation is proposed and it is demonstrated that the surface structure of AONWAs can be utilized to transport objects ranging from a polystyrene microsphere to a macroscopic PET sheet (lower figures). Unidirectional wetting of the surface and the relation between the anisotropy of the wetting and the NWs' obliquity are described. Potential applications of the AONWAs include fluidic diodes, drug delivery systems, and self-cleaning without a liquid. Detailed facts of importance to specialist readers are published as ”Supporting Information”. Such documents are peer-reviewed, but not copy-edited or typeset. They are made available as submitted by the authors. Please note: The publisher is not responsible for the content or functionality of any supporting information supplied by the authors. Any queries (other than missing content) should be directed to the corresponding author for the article.

We report an array of polymeric nanowires for effectively immobilizing biomolecules on biochips owing to the large surface area. The nanowires were fabricated in predesigned patterns using an inductively coupled plasma (ICP) etching process. Microfluidic biochips integrated using the substrates with arrays of nanowires and polydimethylsiloxane channels have been demonstrated to be effective for detecting antigens, and a detection limit of antigens at 0.2 μg mL(-1) has been achieved, which is improved by a factor of 50 compared to that based on flat substrates without the nanowires. In addition, the high sensitivity for clinical detection of human immunodeficiency virus (HIV) antibody has also been demonstrated, showing a 20 times enhancement in fluorescent signal intensity between the samples with positive and negative HIV.

With the fast development of the Internet of Things, the requirements of system miniaturization and integration have accelerated research on multifunctional sensors. Based on the triboelectric nanogenerator, a self-powered multifunctional motion sensor (MFMS) is proposed in this work, which is capable of detecting the motion parameters, including direction, speed, and acceleration of linear and rotary motions, simultaneously. The MFMS consists of a triboelectric nanogenerator (TENG) module, a magnetic regulation module, and an acrylic shell. The TENG module is formed by placing a free-standing magnetic disk (MD) on a polytetrafluorethylene (PTFE) plate with six copper electrodes. The movement of the MFMS causes the MD to slide on the PTFE plate and hence excites the electrodes to produce a voltage output. The carefully designed six copper electrodes (an inner circle electrode, an outer circle electrode, and four arc electrodes between them) can distinguish eight directions of movement with the acceleration and determine the rotational speed and direction as well. Besides, the magnetic regulation module is applied here by fixing a magnetic cylinder (MC) in the shell, right under the center of the PTFE plate. Due to the magnetic attraction applied by the MC, the MD will automatically return to the center to prepare for the next round of detection, which makes the proposed sensor much more applicable in practice.

Abstract Although dielectric elastomer actuators (DEAs) are promising artificial muscles for use as visual prostheses in patients with oculomotor nerve palsy (ONP), high driving voltage coupled with vulnerable compliant electrodes limits their safe long‐term service. Herein, a self‐healable polydimethylsiloxane compliant electrode based on reversible imine bonds and hydrogen bonds is prepared and coated on an acrylic ester film to develop a self‐healable DEA (SDEA), followed by actuation with a high‐output triboelectric nanogenerator (TENG) to construct a self‐powered DEA (TENG‐SDEA). Under 135.9 kV mm −1 , the SDEA exhibits an elevated actuated strain of 50.6%, comparable to the actuation under DC power. Moreover, the mechanically damaged TENG‐SDEA displays a self‐healing efficiency of over 90% for 10 cycles. The TENG ensures the safe using of TENG‐SDEAs and an extraocular‐muscle‐like actuator with oriented motion ability integrated by several TENG‐SDEAs is constructed. Additionally, the SDEA is directly used as a flexible capacitive sensor for real‐time monitoring of the patient's muscle movement. Accordingly, a medical aid system based on a conjunction of the extraocular‐muscle‐like actuator and a flexible capacitive sensor is manufactured to help the patients suffering from ONP with physical rehabilitation and treatment.